接触弧,arc of contact
1)arc of contact接触弧
英文短句/例句
1.DETERMINATION OF THE LENGTH OF THE CONTACT ARC IN COLD ROLLING AND CALCULATION OF THE ROLLING FORCE冷轧板材接触弧长度的确定及轧制力计算
2.k-and-wiper switch触排和接帚开关;触排及弧刷转接器;双动选择器
3.A study of the effect of contact strength on spiral bevel gears affected by contacting area etc接触区等对弧齿锥齿轮接触强度影响的研究
4.Tooth mesh and contact analysis of spiral bevel gears based on MATLABMATLAB环境下的弧齿锥齿轮啮合接触分析
5.Contact Zone Simulation Analysis of Spiral Bevel Gear Teeth Faces in Heavy Load Transmission重载弧齿锥齿轮齿面接触区仿真分析
6.THE EFFECTS OF CONTACT DEFORMATION OF LINE-CONTACT CATT CYLINDER GEAR ON THE BENDING STRESS IN THE FILLETS线接触圆弧齿线圆柱齿轮齿面接触变形对齿根应力的影响
7.ON THE THREE DIMENSIONAL CONTACT STRENGTH OF FINAL ARC FIR TREE BLADE ROOT AND ROTOR末级圆弧枞树型叶根与轮缘三维接触强度研究
8.The Design of High Speed Globodial Cam Indexing Mechanism for a Type Point Contact点接触式高速弧面分度凸轮机构的设计
9.Tooth Contact Analysis and Cutting Parameters Modification of Small-modulus Spiral Bevel Gears;小模数弧齿锥齿轮的接触分析与切削参数修正
10.Roughness and contact angles of micro-arc oxidation coating on the surface of titanium纯钛表面微弧氧化膜的粗糙度与接触角
11.Discussion on Permanent Magnetic Actuator With Non-Plane Contact and Double-Acting Vacuum Interrupter非平面接触永磁机构与双动式真空灭弧室探讨
12.Geometrical Contact Analysis of the Flow-dividing Transmission System of an Arc-tooth Cone Gear弧齿锥齿轮分流传动系统几何接触分析
13.Transmission Analysis of an Arc Teeth Synchronous Belt Considering the Complex Contact Conditions复杂接触条件下圆弧齿同步带啮合传动分析
14.Image acquisition and pre-processing of spiral bevel gear contact spots弧齿锥齿轮接触斑点图像采集及预处理
15.The worn wheel tyre contact surface has a concave revolutionary curved form with two principal curvatures.磨耗后的车轮接触面,是内凹圆弧的旋转形成面,有两种主曲率。
16.Basom observed the contact angle of water against silane-treated E glass to be about 1. 2 rad.巴索母观察到水对硅烷处理的E玻璃接触角大约是1．2弧度。
17.Analysis of Dielectric Recovery Strength and Reignition Process in Iron Splitters Chambers of AC Contactor接触器栅片灭弧室介质恢复强度及重燃过程的分析
18.The working condition of circular-arc-tooth-trace (CATT) cylinder gear has certain effect on the contact zone between its tooth flanks.外部条件对圆弧齿线圆柱的齿轮的齿面接触区产生一定影响.
相关短句/例句
contact arc接触弧，接触弧片
3)touch striking arc接触引弧
1.The technology of small currenttouch striking arc has become a tendency of automatic striking arc technology in TIG welding process.小电流接触引弧是目前钨极氩弧 (TIG)焊自动引弧的发展趋势 ,本文在分析了小电流接触引弧工作原理的基础上 ,指出影响引弧成功率的主要因素是短路电流和短路时间、热引弧电流和热引弧时间。
4)contact length接触弧长
1.Some characteristics concerning the chip formation component force ratio c, specific cutting force k_0,the coefficient of friction μ,thecontact length Lc and the residual stock removal △y have been obtained.本文对接触板式砂带平面磨削主要机理参数和残留量进行了大量的试验研究,得出了接触板式砂带平面磨削时切屑变形分力比C、单位磨削力K_0、摩擦系数μ、接触弧长L_c以及磨削残留量△y的特点。
2.An integrated improvement on the force model has been made in the present investigation, including model structure, measuring methods and sub-routine of three most important variables-flow stress,contact length and friction coefficient.本研究在模型结构和3个最重要自变量——材料的流变应力,弹塑性接触弧长和界面摩擦系数——的测定方法和计算模型上进行了全面改进和更新,建立起高精度冷轧轧制力数学模型,将人工神经网络(ANN)处理前的预报精度提高到了5%以内。
5)contacting electric arc接触电弧
6)electrical contact arc电接触弧
延伸阅读
接触弧接触弧arc of contact1 ieehuhu接触弧(are of eontaet)札制过程中变形金属与札辐表面相接触的曲面，即咬入角a所对应的曲面(见图)AB。接触弧的长度则按该曲面水平投影的直线段AC的长度l来衡量，Ac也叫变形区长度。接」口接触弧触弧的长度l等于咬入角的正弦与轧辊半径R的乘积，即l二Rsina。在建立轧制过程时，接触弧的长度是变化值。当轧制过程建成之后，变形金属充满变形区，此时接触弧的长度达到最大值并保持不变。当两个轧辊直径不相等时以及当轧辊和轧件产生弹性压缩时，接触弧的长度都将发生变化。(余望)
