共晶化合物,eutectic compounds
1)eutectic compounds共晶化合物
1.The result shows that the welding seam consists of Al-matrix and Al-Sieutectic compounds.结果表明,焊缝主要组成相是以Al为基体的Al-Si共晶化合物:焊缝区域硬度值从上表面到背面有下降趋势,且平均值略高于母材。
英文短句/例句
1.Preparation and Analysis of Single Crystal of co-Crystal of Aminium Perchlorates有机胺高氯酸盐共晶化合物的单晶制备与表征
2.Studies on the Structure and Properties of Co-crystal Compound of Perchloric Amine Salt高氯酸胺盐共晶化合物的结构与性能表征
3.Progress in Composites of Oxide/Oxide Eutectics氧化物/氧化物共晶复合陶瓷研究进展
4.RESEARCH PROGRESS ON OXIDE EUTECTIC IN-SITU CERAMIC COMPOSITES氧化物共晶自生复合陶瓷的研究进展
5.smectic compound近晶［脂状］化合物
6.Anti-abrasive Wear Composite of Carbide Eutectic/Cu-Mn-Ni Cupronickel;碳化物共晶体/锰白铜抗磨料磨损复合材料
7.Research of Automatic Analysis for High Alloy Eutectic Carbide;高合金工具钢共晶碳化物自动分析技术研究
8.Morphology Improvement of Eutectic Carbides in Low Alloy Wear Resistant Cast Iron低合金耐磨铸铁共晶碳化物形态改善的研究
9.A Study on Phase-mixing of Poly(∈-caprolactone)/Poly(vinyl chloride)after the Melting of Crystals聚已内酯/聚氯乙烯共混物晶体熔化后相混合情况
10.Large eutectic ledeburite is not found.合金层中的碳化物细小、均匀、弥散,无粗大的共晶莱氏体组织。
11.Separation of Intermetallic Compounds in the Microstructure of Eutectic Sn-Ag-Zn Solder Solidified at Different Cooling Rates;宽冷却速度下共晶Sn-Ag-Zn焊料组织中金属间化合物的析出
12.Wetting kinetics of Sn-Pb eutectic solder on Cu and Cu-Sn intermetallics substratesSn-Pb共晶钎料在铜基板及金属间化合物基板上的润湿动力学
PARISON OF AROMATIZATION PERFORMANCES BETWEEN COCRYSTALLIZATION AND MIXTURES OF MCM-49 AND ZSM-35MCM-49与ZSM-35的共结晶及混合物的芳构化性能比较
14.Amorphous/crystalline blend effects on the performance of polymer-based photovoltaic cells非晶/结晶共混对聚合物光伏电池性能的影响
15.Study on the Bi-Added Hypereutectic Al-Si Alloys;Bi合金化过共晶Al-Si合金的研究
16.A novel accumulation mode complementary GAAC FinFETs inverter with hybrid orientation SOI substrate一种新型混合晶向积累型圆柱体共包围栅互补金属氧化物场效应晶体管
17.nonfaceted-non-faceted eutectic alloy非小面化-非小面化共晶合金
18.Synthesis of Multi-amino and Multi-carboxylic Compounds Based on Magnetic Resonance Imaging Agent and Crystal Structure of Metal Complexes基于核磁共振造影剂的多氨多羧化合物的合成与金属配合物晶体结构
相关短句/例句
eutectic mixture共晶混合物
3)eutectic carbide共晶碳化物
1.These structures make the quenching temperature to be rise and the overtemperature structure and the uniformity ofeutectic carbide in the steel are the major reasons of quenching crack.结果表明,由于刨齿轮W18Cr4V钢共晶碳化物不均匀度严重超标,网状碳化物、莱氏体的存在使得淬火加热温度过高,造成组织过热,增加了材料的脆性,降低了刨齿刀的力学性能,导致刨齿刀淬火时产生裂纹。
2.Results show that, when suitable RE is added into high carbon high speed steel,the austenite andeutectic carbides have been changed.热处理后,共晶碳化物大部分变成团球状且分布均匀。
3.After heat treatment, networkeutectic carbides of cast Cr12 die steel are changed into nodular and dispersed ones in the matrix.铸造Cr12模具钢中共晶碳化物呈网状分布于晶界上,且枝晶粗大,经Al-Zn变质处理,共晶组织明显细化,离异共晶数量增多;经热处理后,Cr12模具钢共晶碳化物由网状变为粒状和块状且均匀分布于基体中,同时,硬度有所降低,冲击韧性得到明显提高。
4)Eutectic carbides共晶碳化物
1.Study of fractal dimension on the unevenness of eutectic carbides of Cr12 steel;Cr12钢共晶碳化物不均匀度的分维研究
2.The results show that, the morphology and distribution of the eutectic carbides are improved and the grain refinement is better with the increase of compound modifier addition within 1.0%范围内,随着复合变质剂含量的逐渐增加,共晶碳化物的形貌和分布得到了改善,晶粒得到细化,分布趋于均匀,轧辊用高速钢的硬度略有下降,但韧性有很大提高。
3.The result shows that the morphology and distribution of eutectic carbides in Cr12 steel under new process were improved, spheroidal pearlite and fine grain of alloy carbides were obtained,mechanics properties were enhanced.试验结果表明,经该工艺处理的Cr12钢,组织中共晶碳化物形态和分布得以明显改善,最终热处理后获得了均匀的细隐晶回火马氏体和弥散分布的细粒状合金碳化物的显微组织,获得了优异的综合力学性能,使热处理后的拉丝模和冷冲模的使用寿命比常规热处理工艺处理的使用寿命提高1～2倍。
5)eutectic silicide共晶硅化物
1.By using the cyclic oxidation experiments and in-situ X-ray diffraction, this paper studied the oxidation behavior of Mo_3Si-Mo_5Si_3eutectic silicide at 600~1 200 °C and analyzed the low temperature oxidation mechanism and high temperature pest phenomena.利用循环氧化和原位 X射线衍射法 ,研究了 Mo3 Si- Mo5Si3 共晶硅化物在 60 0～ 1 2 0 0°C氧化行为 ,分析了低温氧化规律和高温氧化瘟疫现象 。
6)eutectic carbide granulation共晶碳化物粒化
延伸阅读
共晶共沉淀分子式：CAS号：性质：共沉淀法之一，指无法结晶的微量物质与常量物质产生共结晶沉淀而被载带出来。
